RECARO BASE FRAME SEAT RAIL LEFT SEAT FOR NISSAN FAIRLADY Z Z33 2081.098.1

RECARO

BASE FRAME SEAT RAIL LEFT SEAT

2081.098.1

NISSAN FAIRLADY Z Z33

Model year: 2002-08-2008-10
Special notes: For vehicles with side airbags, the airbag warning light must be turned off. The seating position is a few mm higher than the lowest position of the factory seat (when using ST-JJ). The driver's seat has a seat offset of about 15 mm on the door side (the Recaro moves closer to the door), and the passenger seat has a seat offset of about 5 mm on the door side (the Recaro moves closer to the door). The forward sliding amount is reduced by about 50 mm compared to the factory.
Notes / Interference information: For Trend, Style, Sport-J, JJ, JC, D, and DC, the backrest side and door armrest interfere by a few mm. For CSE, the seat cushion side and center console interfere by about 10 mm, and the seating position is higher due to the use of a spacer. For CS, the seating position is higher due to the use of a spacer. For LX (including Ergomed), LS, LT, SR-1, 2, 3, 4, and 5, the door-side recliner dial is difficult to operate. For SP-#, the SP-G offset adapter set (product number 1600094J) is required. For RS/TS-#, the RS/TS-G offset adapter set (product number 1700001J) allows the handle offset to be adjusted in 5mm increments from 5mm to a maximum of 15mm. (Please consult your dealer regarding interference with the console side (shift, etc.) when installing.) For RMS, adjust to the optimal position (front-to-back height, left-to-right offset 0/5/10mm) using the separately sold RMS side adapter. Also, if there is interference with the interior, it can be alleviated by adjustment. For RCS, adjust to the optimal position (front-to-back height, left-to-right offset 0/5/10mm) using the separately sold RCS side adapter.
Position: New structure frame. One-position type.
Armrest: Not compatible
Compatible seats: LX / LX-# / LX-VS / LX-VF / LX-VL / Ergomed / ErgomedC / ErgomedD / ErgomedE / ErgomedLD / ErgomedMV (IS-84 base)
Classic LX Pepita / Classic LX Spektrum
LX-F (IS-05 base)
LS / LS-# / LT-#
CS / CR / CG / Conformed
CSE
Pro Racer RMS RMS should be installed after adjusting to the optimal position (front-rear height, left-right offset 0/5/10mm) using the separately sold RMS side adapter . Also, if there is interference with the interior, it can be mitigated by adjusting it. New Orthoped (with Recaro vent)
RCS Please adjust the RCS to the optimal position (front/rear height, left/right offset 0/5/10mm) using the separately sold RCS side adapter before installation. *Please choose from the following two types. ・RCS side adapter ・RCS stainless steel side adapter set SR-2 late model / SR-3 / SR-4 / SR-5 / SR-VF / SR-IMPACT / SR-IMPACT Pro
Rally Special / First generation SR / SR-2 early model
Late model A-8
Early model A-8
SP-A / SP-G / SP-G2 / SP-G3 / SP-GT / SP-GT2 SP-# and Racer require the separately sold SP-G offset adapter set . SP-AN / SP-GN / SP-GN 2 SP-AN / SP-GN / SP-GN 2 require the separately sold SP-GN side adapter set (product number 1600110J). AM19 TREND-J/JJ/JC
AM19 STYLE-J/JJ/JC
AM19 SPORT-J/JJ/JC
AM19 TREND-JS
AM19 STYLE-JS
AM19 SPORT-JS
AM19 TREND-D/DC
AM19 STYLE-D/DC
AM19 SPORT-D/DC/MAGNIFICA CL222HV
TS-G / RS-G / TS-W / RS-W For RS/TS-# series, please choose from two types of side adapter set or offset adapter set for RS/TS-G, sold separately. [Priority on seating position] Side adapter set [Priority on offset] Offset adapter set for RS/TS-G Handle offset can be adjusted to 5/10/15mm left and right. (Seating position is raised by +5mm.) SP-X
SR-6 /SR-11/SR-7
SR-S
SR-C/ SR-7F
Sportster
CrossSportster

(Note) This product cannot be installed on any seats other than those listed in the matching information below. Side airbag canceller included. Excluding the Roadster. Vehicles with height adjusters have not been confirmed.

Images are for illustration purpose only. Actual product may vary.